Some time ago, we finished the first test assembly of the Mig-23ML from the Ukrainian manufacturer Clear Prop Models. You can see the results here:
viewtopic.php?p=2518811#p2518811
The first assembly was aimed at checking the convergence of all elements, identifying flaws, and seeing what and where can be improved. The first test model was not painted.
Now we are starting the second test assembly of this model, this time a full-fledged one. It is planned to assemble a modification of the MiG-23MLA, Czechoslovakia, serial number 0390324850.
Zdravím vás milá modelářská komunita!
Před časem jsme dokončili první testovací montáž modelu Mig-23ML. Její výsledky si můžete prohlédnout zde:
viewtopic.php?p=2518811#p2518811
První sestava byla zaměřena na kontrolu konvergence všech prvků, identifikaci nedostatků a zjištění, co a kde lze zlepšit. První testovací model nebyl lakován.
Nyní zahajujeme druhou testovací montáž tohoto modelu, tentokrát plnohodnotnou. Plánuje se montáž modifikace MiGu-23MLA, československá strana 4850:
On the banner this board is shown as of May 1983, but I will assemble this board as of February 1983 - when it still had a completely standard factory color.
The first test assembly confirmed all the expectations built into the model at the design stage. However, as a result, it was decided to make a number of improvements. One such improvement was the development of more detailed out-of-the-box photo-etching:
Na banneru je tato deska zobrazena od května 1983, ale tuto desku budu montovat od února 1983 - kdy ještě měla zcela standardní tovární barvu.
První zkušební montáž potvrdila všechna očekávání zabudovaná do modelu ve fázi návrhu. V důsledku toho však bylo rozhodnuto provést řadu vylepšení a vylepšení. Jedním z takových vylepšení byl vývoj podrobnějších fotoleptů:
The number of photo-etched parts has been increased by more than one and a half times compared to the original version, the detailing of each element has been revised and, if possible, finalized.
This build of the model will also feature an additional Clear Prop Models resin accessories. Details are under development. At the moment, we can demonstrate the resin nozzle:
Počet leptaných dílů se oproti původní verzi zvýšil více než jedenapůlkrát, detaily každého prvku byly revidovány a pokud možno dopracovány.
Tato sestavení modelu bude také obsahovat dodatečný trh s náhradními díly z pryskyřice ClearProp. Podrobnosti jsou ve vývoji. V tuto chvíli můžeme demonstrovat trysku z pryskyřice:
A distinctive feature of this accessories (in addition to surface detailing) is the implementation of the peculiarity of the nozzle sag in the parking position. In out-of-the-box plastic, the nozzle is strictly symmetrical along the axis. This is entirely true for the flight configuration, but not for the parking one.
During the assembly process, I plan on my own all kinds of improvements by hand. The model does not need any recutting, but I plan to improve and supplement the detailing of individual elements.
Assembly begins with the cockpit. The first thing I can show is the cabin floor with all the elements:
Charakteristickým rysem tohoto následku (kromě povrchových detailů) je implementace zvláštnosti prověšení trysky v parkovací poloze. V hotovém plastu je tryska přísně symetrická podél osy. To zcela platí pro konfiguraci letu, ale ne pro konfiguraci parkování.
Během procesu montáže plánuji sám všemožná vylepšení s pery. Model nepotřebuje žádné přeřezávání, ale plánuji vylepšit a doplnit detailing jednotlivých prvků.
Montáž začíná kokpitem. První věc, kterou mohu ukázat, je podlaha kabiny se všemi prvky:
I made a new throttle so that this part of the cabin looked more voluminous. Native throttle has already been removed.
Znovu jsem vyrobil ovládací knoflík motoru, aby tato část kokpitu získala objemnější vzhled.
In fact, this is the start. As updates become available, I will post them.
Takový začátek. Jak bude montáž modelu postupovat, budu vkládat nové fotky.
Naposledy upravil DimaADA dne 09 úno 2024, 21:57, celkově upraveno 1