Diskusní fórum modelářů

Few days ago i started work on something different, than usual 32 scale kit, resin flying boat produced by Czech Omega Models, Hansa Brandenburg W20, packed in small, smaler than A5 format box, actualy measured4x11x21cm. Omega Models and Mr. Jan Pala do the great job producing this kit. Beautifuly casted without any bubble , with great decal sheet for Losenge cammo scheme.
Only instruction is quite problematic, without exploded view, just few sheets of scale drawings, brief history and paint instructions.
Googling over the web, find some photos and usefull info about this small flying boat, which will help me in completing this model.

W20 will look like this 1/48 scale model,

[ Externí obrázek z nezabezpečeného zdroje ]

Box art, casted parts and instruction sheets,

[ Externí obrázek z nezabezpečeného zdroje ]

[ Externí obrázek z nezabezpečeného zdroje ]

[ Externí obrázek z nezabezpečeného zdroje ]

[ Externí obrázek z nezabezpečeného zdroje ]

[ Externí obrázek z nezabezpečeného zdroje ]

And some work was done, cleaning casting blocks and polishing some details,

[ Externí obrázek z nezabezpečeného zdroje ]

Build up photo story will follow,

Todays update,

Parts cleaned and test fitted,

[ Externí obrázek z nezabezpečeného zdroje ]

Copper wire, 1 mm dia, used for horizontal-vertical tail joint,

[ Externí obrázek z nezabezpečeného zdroje ]

And superglued,

[ Externí obrázek z nezabezpečeného zdroje ]

Same system used for fuselage-tail joint,

[ Externí obrázek z nezabezpečeného zdroje ]

Test fitted, just to feel the real plane shape, neat little flying boat,

[ Externí obrázek z nezabezpečeného zdroje ]

Rotary engine and prop (photo out of focus, damn macro mode)

[ Externí obrázek z nezabezpečeného zdroje ]

Tail struts supplied with kit are too short, new one made from styrene sheet (1mm,)

[ Externí obrázek z nezabezpečeného zdroje ]

Tailplane completed ,

[ Externí obrázek z nezabezpečeného zdroje ]

nice work...

Its time for more pictures of this Brandenburg flying boat,

First, complex and problematic( lack of good photos and drawings, even on the internet), so, i do some research and use good drawings from 1/72 scale CMR kit of same plane.

Steel wire, styrene sprues,superglue and supplied resin parts, here is the few steps of engine pylon build,first made an construction jig on wooden plank,

[ Externí obrázek z nezabezpečeného zdroje ]

[ Externí obrázek z nezabezpečeného zdroje ]

[ Externí obrázek z nezabezpečeného zdroje ]

Fuselage is primed with filler/primer spray and polished,

[ Externí obrázek z nezabezpečeného zdroje ]

And wheel cart is made, nice etched wheels, "O-Ring"(rubber ring) for tires,

[ Externí obrázek z nezabezpečeného zdroje ]

Superglued etched parts on rubber rings,

[ Externí obrázek z nezabezpečeného zdroje ]

Cart base was made of styrene sheets,

[ Externí obrázek z nezabezpečeného zdroje ]

And "Voila", fuselage seats on cart,

[ Externí obrázek z nezabezpečeného zdroje ]

Also do some spraywork over the wings, not find exact FS for topside surfaces, and use some paint chips and colour profiles supplied within the kit , to mix my own Gray.
Anyway, on the wing topsides will go the Losenge decal, undersides are doped linen fabric, this will be easily mixed from some tan/white/lacquer.

[ Externí obrázek z nezabezpečeného zdroje ]

Just a few bits on Brandenburg, finished cockpit,

[ Externí obrázek z nezabezpečeného zdroje ]

and sprayed wing undersurfaces in Doped Linen -Fabric paint ,

[ Externí obrázek z nezabezpečeného zdroje ]

Its time for decal job.
Hard work, Lozenge cammo, no room for mistake, only one set of decals.

I use PRONTO ( read FUTURE) as decal base coat, which gives me better adhesion on such large decal sheet.

[ Externí obrázek z nezabezpečeného zdroje ]

Aileron decals are printed too small and in wrong shape, so i have to cut and apply each hexagonal segment from leftover decals to made decent aileron Lozenge camouflage.
Takes me few hours for this two ailerons.

[ Externí obrázek z nezabezpečeného zdroje ]

[ Externí obrázek z nezabezpečeného zdroje ]

Removing decal film from leading and trailing edges is easy using 800-1000 sand paper and carefully sanding the film on the wing edge.

[ Externí obrázek z nezabezpečeného zdroje ]


And here is finished decal job, sealed with another coat of Pronto,resting overnight to dry .
Note, Iron Cross decals are printed on white decal film,and each cross must be carefully trimmed prior the transfer on the wings.

[ Externí obrázek z nezabezpečeného zdroje ]

Just a short update of this model project, after the two days of Lozenge cammo decal left to dry , i trimmed and glued wing struts and do some wings rigging.

I use kit instruction, as well some web research for photos and drawings and became totaly confused with wing struts and rigging.
Only three real W20 were build, and looks that each have different struts/rigging configuration, so i stay with kit instruction data, despite 1/72 scale CMR kit instruction gives different diagram for rigging.

I made wing rigging with .35mm steel wire used for "Control Line"flying models, drill the ,5mm holes in the wings and superglued the wires .

[ Externí obrázek z nezabezpečeného zdroje ]

There is no need to paint the wires, just clear cote to save it from rusting.
Need to paint wing struts, underwing pontoons in light gray cammo paint,

[ Externí obrázek z nezabezpečeného zdroje ]

Temporary assembly, just to see the overall look of this model.
[ Externí obrázek z nezabezpečeného zdroje ]

Brandenburg "KAPUTT"

[ Externí obrázek z nezabezpečeného zdroje ]

[ Externí obrázek z nezabezpečeného zdroje ]

[ Externí obrázek z nezabezpečeného zdroje ]

[ Externí obrázek z nezabezpečeného zdroje ]

[ Externí obrázek z nezabezpečeného zdroje ]

[ Externí obrázek z nezabezpečeného zdroje ]

[ Externí obrázek z nezabezpečeného zdroje ]

And few more, on the mirror base,

[ Externí obrázek z nezabezpečeného zdroje ]

[ Externí obrázek z nezabezpečeného zdroje ]

[ Externí obrázek z nezabezpečeného zdroje ]

[ Externí obrázek z nezabezpečeného zdroje ]

A great kit from Omega Models, pleasure to build, a nice and eyecatching model for any 1/32 scale collection.

Very nice work

Wow very nice job

Hi, it is funny subject nicle build!
By the way, may I ask you what kind of Pronto you have used? Do you have picture of bottle?

Thanx for the comments,


Pronto Cera Pavimenti is the "chemistry" used for decals and clear parts, similar to "Future".
I use this, old bottle
[ Externí obrázek z nezabezpečeného zdroje ]
and new bottle
[ Externí obrázek z nezabezpečeného zdroje ]

thanks a lot!

Great work .. congratulation !!!